Final Exam

You are allowed 45 minutes to complete the exam. You cannot change your answers.

You need a passing grade of 80% to receive your certificate.
Your final mark will appear at the end of the exam.

If you do not receive a passing grade, you will be given and opportunity to review the course and retake the exam once again.

Passing grades will be receive your certificate.

Time limit: 0

Quiz Summary

0 of 25 Questions completed

Questions:

Information

You have already completed the quiz before. Hence you can not start it again.

Quiz is loading…

You must sign in or sign up to start the quiz.

You must first complete the following:

Results

Quiz complete. Results are being recorded.

Results

0 of 25 Questions answered correctly

Time has elapsed

You have reached 0 of 0 point(s), (0)

Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)

Categories

Not categorized 0%

You have not passed the final exam. Please contact us to review your options.
Congratulations on your successful completion of the Online Crane Training Certification Course. You will now receive your certificate. We appreciate if you could write a review of the course and send it to info@cranetraining.ca so we can improve on the material in the future.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

Current
Review
Answered
Correct
Incorrect

Question 1 of 25

1. Question
The primary danger zone is a 10 ft. circle beneath the load?
- True
- False
Correct

Incorrect
Question 2 of 25

2. Question
Understanding the weight of one cubic foot of steel allows an operator a simple formula for estimating a load of steel?
- True
- False
Correct

Incorrect
Question 3 of 25

3. Question
A safety latch is required on crane hooks in order to prevent a load from coming off the hook.
- True
- False
Correct

Incorrect
Question 4 of 25

4. Question
Any chain in the work area can be used for rigging loads.
- True
- False
Correct

Incorrect
Question 5 of 25

5. Question
The tension on the sling leg doubles when a sling to load angle is used at 30 degrees compared to 90 degrees.
- True
- False
Correct

Incorrect
Question 6 of 25

6. Question
The capacity sign on a hoist or crane can be used as a general indication of the loading capability of a crane, the operator should make his own determination based on various factors and his experience.
- True
- False
Correct

Incorrect
Question 7 of 25

7. Question
A side pull is created when the operator attempts to pull a load from an area outside of the vertical lifting area of the hoist.
- True
- False
Correct

Incorrect
Question 8 of 25

8. Question
To correct a swinging load, the operator should time the movement of the crane or trolley from the center of the swing directly into its highest arch.
- True
- False
Correct

Incorrect
Question 9 of 25

9. Question
In addition to specific markings, a below the hook device needs to be checked for defects prior to every lift?
- True
- False
Correct

Incorrect
Question 10 of 25

10. Question
Any defect noted by the operator must be reported to the supervisor at the end of the shift.
- True
- False
Correct

Incorrect
Question 11 of 25

11. Question
An operator who is leaving the hoist or crane unattended must place the load on the floor in such a way that the load is solidly supported.
- True
- False
Correct

Incorrect
Question 12 of 25

12. Question
The safety of an eyebolt is questionable, when the load is applied from the side or when it is not tightened into its fitting?
- True
- False
Correct

Incorrect
Question 13 of 25

13. Question
All slings used for a lift should be inspected before every lift.
- True
- False
Correct

Incorrect
Question 14 of 25

14. Question
Employees should not work under a load except in an emergency.
- True
- False
Correct

Incorrect
Question 15 of 25

15. Question
A minimum sling angle of 45 degrees to the horizontal is a good standard to maintain.
- True
- False
Correct

Incorrect
Question 16 of 25

16. Question
An upper limit switch is a safety device and should never be tested with a load on the hook.
- True
- False
Correct

Incorrect
Question 17 of 25

17. Question
A pre-shift inspection is required once a week.
- True
- False
Correct

Incorrect
Question 18 of 25

18. Question
It is not necessary to make direct contact with electrical power in order for power to enter the crane or load.
- True
- False
Correct

Incorrect
Question 19 of 25

19. Question
Any equipment used to lift a load into the air will be considered as critical application equipment.
- True
- False
Correct

Incorrect
Question 20 of 25

20. Question
The operator is responsible for the safety of his load.
- True
- False
Correct

Incorrect
Question 21 of 25

21. Question
Which of the following is not a proper grade of rigging chain?
- Grade 3
- Grade 8
- Grade 10
- Grade A
Correct

Incorrect
Question 22 of 25

22. Question
Select the most correct statement.
- The operator will accept operating signals from two or more persons.
- The operator will accept operating signals from a bystander.
- The operator will accept signals only from a qualified, designated signalman.
- The operator will accept signals only from a qualified, designated signalman but will accept a stop signal from anyone.
Correct

Incorrect
Question 23 of 25

23. Question
Who is responsible for safety of the load once it is lifted?
- The person that tells you what to do.
- Anyone who is in the area and was paying attention.
- The operator or designated signaler.
- Anyone on the safety committee.
- Any person that can fire you if you're not fast enough.
Correct

Incorrect
Question 24 of 25

24. Question
To prevent shock loading:
- Begin raising the load at low speed then go to the high speed
- The trolley should be centered over the load.
- The load should be mounted on solid blocking.
- The rigging is set in such a way that the load cannot shift.
- All of the above
Correct

Incorrect
Question 25 of 25

25. Question
Which of the following is NOT a function of Pre-Operational Inspections?
- To ensure that no damage will knowingly occur during operation.
- To spot any damage that may have occurred during prior use.
- To meet the requirements of the manufacturer's warranty.
- To ensure that the crane is safe and maintained in such condition that when in use it will not endanger other workers.
Correct

Incorrect

Login

Accessing this course requires a login. Please enter your credentials below!

Username or Email Address

Password

Remember Me

Lost Your Password?

Register

Don't have an account? Register one!

Register an Account

Username

Email

Registration confirmation will be emailed to you.